8 easy car projects for DIY beginners – Kyle Smith Hagerty


If you want to work on your own car, and have asked around for the best projects to start with, you’ve probably been given bad advice.

The most popular suggestions are often changing your oil and replacing your brake pads and/or rotors—in other words, high-consequence projects. If you are mechanically inclined, have a knowledgable supervisor, or are not as new to DIY as you say you are, these aren’t the worst ideas. For a true newcomer, however, oil- and brake changes are two of the riskiest places to start.

The first bolt you tighten shouldn’t be one as delicate as the oil drain plug; it’s too easy to over-torque, causing the threads to strip and the oil to leak. We want you to enjoy a long life of working on cars, not turn your engine to scrap metal after it drains all its oil. We certainly don’t want you to get in a collision because your brakes failed: Brakes are a safety requirement, and should never be disassembled and reassembled by a newbie alone.

The good news? There is lower-hanging fruit on the DIY tree. These eight projects might not be sexy, but each is a great way to learn how your car works. Better yet, your car will be safe to drive the entire time.

A good chassis lubin’

The chassis of a vintage car is peppered with grease zerks that allow a mechanic to push fresh lubricant into critical junctions and pivots—think suspension bushings and steering joints. (If you have a modern car, skip this one: Due to cost cutting and planned obsolescence, zerks are no more.)

Often, lubing a chassis can be accomplished without lifting the car. Squeezing in new lubricant from a grease gun is as simple as attaching the coupler and pumping grease into the fitting until you feel light resistance on the handle or see a small bit of grease push past the seals of the component you are working on. Take this opportunity to try and wiggle the part you are greasing. There will be a little movement, but nothing should feel sloppy or loose. If it does, congrats—you may have found your next project.

Flush away your (coolant) problems

Read any shop manual and you will find that a vehicle’s coolant should be changed on a relatively short interval. Since that coolant exists in a closed loop (we can’t see or touch it) and the temperature gauge behaves like it should, your car’s coolant is probably fine, right? Sort of.

Aging coolant—or improper coolant, since you never know what the previous owner put in—can cause lots of damage to an engine and to the heater core. Flushing coolant is simple and rarely requires special tools. (When it does, the tools are affordable.) Any problems will be signaled by the temp gauge on your car’s dash. After a coolant flush, overheating is common, usually due to an air bubble left in the system—another issue that is easily dealt with on vintage cars. Newer models, less so.

Take a brake … to inspect

To be clear: We are not telling you to work on your brakes; we’re telling you to inspect them.

This project might be the first time you put a car up on jack stands, thus giving you a chance to learn the proper jack points and technique before removing the car’s wheels and visually looking over its brakes.

What are you looking for? Pad thickness and rotor condition on disc-brake systems, drum condition and shoe life on drum setups. Keep an eye out for any fluid leaks: There should be no grease buildup or oil film on anything brake-related. If there is, talk to a pro. In the meantime, put the wheels and tires back on, and practice getting the car back on the ground before fully torquing the lug nuts.

Polish it off

Ever since detailing became all the rage a few years ago so, there is no shortage of how-to advice and guidance for cleaning your car—no matter what model year it is. Polishing your car’s paint requires you to get familiar with the vehicle and to understand the various processes, techniques, and tools of the detailing trade. Here are a few places to start, whether you’re washing off the first coat of dirt, trying clay for the first time, or simply trying to avoid the biggest mistakes.

Read on

Leave a ReplyCancel reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.